[1] Before first useChecking the package contents

After opening the package, check that all items in the list are included in the package. If any item is missing, contact your dealer.

Numbers in ( ) indicate the item quantities.

  • Portable Ultra Short Throw Projector (NOT TRANSLATEDLSPX-P1) (1)
  • Wireless Unit (NOT TRANSLATEDLSPX-PT1) (1)
  • AC adaptor NOT TRANSLATEDVGP-AC19V77 (19.5 V / for the projector) (1)
  • AC adaptor NOT TRANSLATEDLSPX-AC5V2 (5 V / for Wireless Unit) (1)
  • Power cord (CONDITION [EC]4CONDITION [NOT EC]2)
  • IR Blaster (1)
  • Startup Guide (1)
  • Reference Guide (1)
  • Warranty (1)

[2] Before first useLocation of controlsLocation of controls (Portable Ultra Short Throw Projector)

The location of controls of the projector is described below.

  1. Ventilation holes (intake/exhaust)
  2. Projection window

    Projects images onto a wall, table or floor.

  3. Remote control receiver

    Receives signals from the NOT TRANSLATEDHDMI device’s remote control to transfer the signals to the NOT TRANSLATEDHDMI device connected to the Wireless Unit, thus allowing you to operate the NOT TRANSLATEDHDMI device. The Wireless Unit and the NOT TRANSLATEDHDMI device should be connected via the IR Blaster (supplied).

  4. Speakers
  5. Power indicator

    Indicates the status of the power and battery of the projector.

  6. Power button

    DELIMITER [NOT EC]
    Press and hold to turn the projector on/off. Press lightly while the projector is turned on to switch between standby/power-on.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    Press and hold to turn the projector on/off. Press lightly while the projector is turned on to switch between networked standby/power-on.
    DELIMITER [EC]

  7. Illumination sensor

    Measures the ambient illumination to adjust the projection screen brightness.

  8. NOT TRANSLATEDDC IN 19.5V jack

    Connect the AC adaptor NOT TRANSLATEDVGP-AC19V77 (supplied).

  9. Distance sensor

    Measures the distance between the projector and the projection surface.

  10. NOT TRANSLATEDRESET button

    Resets and restarts the projector.

  11. Charge indicator

    Turns on during charging.

  12. Power jack for the stand (sold separately)

    Supplies power to the floor stand (sold separately) when the projector is mounted on the stand.

[3] Before first useLocation of controlsLocation of controls (Wireless Unit)

The location of controls of the Wireless Unit is described below.

  1. NOT TRANSLATEDHDMI IN connector

    Connect an NOT TRANSLATEDHDMI device with a commercially available NOT TRANSLATEDHDMI cable. You can project images from the connected device.

  2. NOT TRANSLATEDHDMI OUT connector

    Connect a TV with a commercially available NOT TRANSLATEDHDMI cable. You can display images from the device connected to the Wireless Unit onto the TV screen.

  3. NOT TRANSLATEDIR BLASTER connector

    Connect the IR Blaster (supplied)

  4. NOT TRANSLATEDDC IN 5V jack

    Connect the AC adaptor NOT TRANSLATEDLSPX-AC5V2 (supplied).

  5. NOT TRANSLATEDPAIRING button

    The projector and the Wireless Unit have already been paired (connection setting) at the time of purchase. When the pairing is removed, such as after maintenance, use this NOT TRANSLATEDPAIRING button to pair them again.

  6. Indicator

    Indicates the status of the Wireless Unit.

[4] Before first useLocation of controlsAbout the indicators

The meanings of the indicators of the projector and the Wireless Unit are shown below:

Projector indicators

  1. Power indicator
    • Turned off: The power is off.
    • DELIMITER [NOT EC]
      Turned on in white (dim): The projector is in standby status.
      DELIMITER [NOT EC]
      DELIMITER [EC]
      Turned on in white (dim): The projector is in networked standby status.
      DELIMITER [EC]
    • Turned on in white (bright): The power is on.
    • Flashing in red
      • Flashing every four seconds: The battery is low.
      • Flashing every two seconds: The temperature inside the projector is too high or too low. Leave the projector at room temperature for a while, then turn in on again.
      • Flashing three times every three seconds: The projector is malfunctioning. Consult your dealer.
  2. Charge indicator
    • Turned off: Recharging is complete.
    • Turned on: Charging.

Wireless Unit indicator

  • Turned on in white: Connected with the projector.
    It lights in white when connected to the wall outlet while the Wireless Unit is turned off. The indicator turns off when the Wireless Unit is ready to use.
  • Flashing in white every second: Software update is in progress.

[5] Before first useLocation of controlsThe home screen of the special application

The items displayed in the home screen of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” are described.

  1. (CONSTANT [2072]Settings) button

    Displays the setting menu.

  2. DELIMITER [NOT EC]
    (standby/power-on) button
    DELIMITER [NOT EC]
    DELIMITER [EC]
    (networked standby/power-on) button
    DELIMITER [EC]

    DELIMITER [NOT EC]
    Switches between standby and power-on.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    Switches between networked standby and power-on.
    DELIMITER [EC]

  3. Projector remaining battery life
  4. CONSTANT [2411]Poster button

    Places the projector in poster mode.

    Tap this button to project a poster, to use the screen mirroring function to project the smartphone’s screen, or to project photos or movies from a NOT TRANSLATEDDLNA device.

    The projector is automatically placed in poster mode just after it is turned on. Tap this to place it in poster mode manually.

    Tap the button under [CONSTANT [2411]Poster] to change the poster type.

  5. “CONSTANT [2410]HDMI” button

    Places the projector in “NOT TRANSLATEDHDMI” mode.

    Tap this button to project images from the NOT TRANSLATEDHDMI device connected to the Wireless Unit.

  6. (control panel) button

    Opens the control panel. You can change the screen brightness, volume, etc.

  7. CONSTANT [2412]Photo cast button

    Tap this button to project a photo or movie stored in the smartphone using the special application.

About the notification screen on the smartphone

DELIMITER [NOT EC]
When the smartphone and projector are connected, the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” is displayed in the notification screen on the smartphone. In this notification, you can switch the projector between standby and power-on, and adjust the volume.
DELIMITER [NOT EC]
DELIMITER [EC]
When the smartphone and projector are connected, the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” is displayed in the notification screen on the smartphone. In this notification, you can switch the projector between networked standby and power-on, and adjust the volume.
DELIMITER [EC]

Flick down from the top edge of the smartphone’s screen to open the notification screen. With an NOT TRANSLATEDiPhone, tap “NOT TRANSLATEDToday” (a) to see the notification of this application.


NOT TRANSLATEDAndroid smartphone

NOT TRANSLATEDiPhone

  1. DELIMITER [NOT EC]
    Standby/power-on button
    DELIMITER [NOT EC]
    DELIMITER [EC]
    Networked standby/power-on button
    DELIMITER [EC]
  2. Volume adjustment button

Hint

  • When two or more projectors are registered to the special application, the device name currently connected is displayed on the home screen.
  • The notification screen may vary depending on the smartphone.

[6] PreparingProjector install location

In addition to a wall, the projector can project photos and movies onto a table or floor. Place the projector in a location appropriate for the projection surface.

Projecting onto the wall

The projected image size varies according to the distance from the wall.

  • 0 cm: 22 inches
  • Approx. 9 cm: 40 inches
  • Approx. 19 cm: 60 inches
  • Approx. 28 cm: 80 inches

Projecting onto a table or floor

The projected image size is 22 inches.

Hint

  • When the projector is lifted up and moved, the projection light is dimmed to prevent it entering the eye.

[7] PreparingPreparing the powerCharging the projector

A lithium-ion rechargeable battery is incorporated into the projector. When the remaining battery life becomes low, the power indicator flashes in red. Connect the supplied AC adaptor to charge the projector.

  1. Connect the power cord (supplied) to the AC adaptor (19.5 V) for the projector (supplied).
  2. Connect the AC adaptor to the NOT TRANSLATEDDC IN 19.5V jack of the projector.
  3. Firmly insert the plug of the power cord into the wall outlet.

    When charging starts, the charge indicator (a) turns on in amber. When charging is complete, the charge indicator turns off.

Hint

  • It takes about four hours to fully charge a flat battery.
  • The charge indicator may turn on to check the remaining battery life even when the battery is fully charged.

[8] PreparingPreparing the powerBattery duration of the projector

The fully-charged projector can be used for approximately two hours.

Hint

  • This battery duration is when [CONSTANT [2073]Picture] is set to [CONSTANT [2086]Preset 1], the volume is set to approximately 80% and a movie is played.
  • Battery duration may vary depending on the ambient temperature or other factors.
  • Battery duration may vary depending on your smartphone.

[9] PreparingPreparing the powerConnect the Wireless Unit to a wall outlet

  1. Connect the power cord (supplied) to the AC adaptor (5 V) for the Wireless Unit (supplied).
  2. Connect the AC adaptor to the NOT TRANSLATEDDC IN 5V jack of the Wireless Unit.
  3. Firmly insert the plug of the power cord into the wall outlet.

    When the power plug is inserted into the wall outlet, the Wireless Unit turns on and the white indicator (a) turns on. When the unit is ready for use, the indicator turns off.

[10] PreparingTurning the power on/offTurning the projector on/off

To turn on

Press and hold the power button (a). The projector is turned on, and the power indicator (b) turns on in white.

To turn off

Press and hold the power button (a). The projector is turned off, and the power indicator (b) turns off.

DELIMITER [NOT EC]
To place the projector in standby status, lightly press the power button (a).
DELIMITER [NOT EC]
DELIMITER [EC]
To place the projector in networked standby status, lightly press the power button (a).
DELIMITER [EC]

Hint

  • The Wireless Unit is turned on when plugged in.
  • DELIMITER [NOT EC]
    When you tap the (standby) button on the home screen of the special application “CONSTANT [2359]Portable Ultra Short Throw Projector Application,” the projector is placed in standby mode. To turn the projector off, press and hold the power button of the projector.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    When you tap the (networked standby) button on the home screen of the special application “CONSTANT [2359]Portable Ultra Short Throw Projector Application,” the projector is placed in networked standby mode. To turn the projector off, press and hold the power button of the projector.
    DELIMITER [EC]
  • When the projector is turned off, it is also disconnected from the access point (wireless router).

[11] PreparingTurning the power on/offCONDITION [NOT EC]Placing the projector in standby statusCONDITION [EC]Placing the projector in networked standby status

DELIMITER [NOT EC]
When you are not going to use the projector for a while, place it in standby status to dim the projection screen.
DELIMITER [NOT EC]
DELIMITER [EC]
When you are not going to use the projector for a while, place it in networked standby status to dim the projection screen.
DELIMITER [EC]

DELIMITER [NOT EC]
Entering standby status
DELIMITER [NOT EC]
DELIMITER [EC]
Entering networked standby status
DELIMITER [EC]

DELIMITER [NOT EC]
Enter standby status either from the projector or the smartphone.
DELIMITER [NOT EC]
DELIMITER [EC]
Enter networked standby status either from the projector or the smartphone.
DELIMITER [EC]
  • Projector body: Press the power button (a) lightly.
  • “CONSTANT [2359]Portable Ultra Short Throw Projector Application”: Tap the (power-on) button (c) on the home screen.

DELIMITER [NOT EC]
The power indicator (c) remains lit in white when the projector is in standby status.
DELIMITER [NOT EC]
DELIMITER [EC]
The power indicator (c) remains lit in white when the projector is in networked standby status.
DELIMITER [EC]

DELIMITER [NOT EC]
Resuming from standby status
DELIMITER [NOT EC]
DELIMITER [EC]
Resuming from networked standby status
DELIMITER [EC]

Resume operation either from the projector or the smartphone.

  • Projector body: Press the power button (a) lightly.
  • “CONSTANT [2359]Portable Ultra Short Throw Projector Application”: Tap the (power-on) button (c) on the home screen.

Hint

  • DELIMITER [NOT EC]
    You can also use the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” displayed in the notification area of the smartphone to switch between standby and power-on.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    You can also use the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” displayed in the notification area of the smartphone to switch between networked standby and power-on.
    DELIMITER [EC]
  • DELIMITER [NOT EC]
    You can use [CONSTANT [2092]Auto on/Networked Standby] of [CONSTANT [2359]Portable Ultra Short Throw Projector Application] to place the projector in standby status automatically in the following conditions.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    You can use [CONSTANT [2092]Auto on/Networked Standby] of [CONSTANT [2359]Portable Ultra Short Throw Projector Application] to place the projector in networked standby status automatically in the following conditions.
    DELIMITER [EC]
    • When the projector is in poster mode and not operated for more than 20 minutes in a dark room
    • At the specified time
    • When your smartphone moves out of range of the projector (for example, you have moved away from the projector with the smartphone)

[12] PreparingInstalling the special application and performing the initial settings

Use the projector’s special application “CONSTANT [2359]Portable Ultra Short Throw Projector Application” to operate and configure the projector. Install “CONSTANT [2359]Portable Ultra Short Throw Projector Application” to your smartphone from Google Play store or App Store.

Compatible smartphone
  • NOT TRANSLATEDAndroid

    NOT TRANSLATEDAndroid 4.4 or later (NOT TRANSLATEDBluetooth 4.0 (NOT TRANSLATEDBluetooth Low Energy) compatible)

  • NOT TRANSLATEDiPhone

    Following devices with NOT TRANSLATEDiOS 9: NOT TRANSLATEDiPhone 4s or later, NOT TRANSLATEDiPod Touch 5th generation or later, NOT TRANSLATEDiPad 3rd generation or later, NOT TRANSLATEDiPad mini

  1. Download and install “CONSTANT [2359]Portable Ultra Short Throw Projector Application” from Google Play store or App Store.
    http://www.sony.net/lspx-p1/store/
  2. After the installation is complete, start “CONSTANT [2359]Portable Ultra Short Throw Projector Application.”
  3. Follow the on-screen instructions to perform the initial settings of “CONSTANT [2359]Portable Ultra Short Throw Projector Application.”

Hint

  • Up to eight smartphones can be registered to the projector. When a further one is to be registered, the oldest registration is overwritten by new one.

[13] PreparingConnecting another device to the Wireless UnitConnecting an NOT TRANSLATEDHDMI device or TV

You can connect an NOT TRANSLATEDHDMI device such as a NOT TRANSLATEDBlu-ray Disc recorder to the Wireless Unit to project images from the NOT TRANSLATEDHDMI device.

To also display images from the NOT TRANSLATEDHDMI device onto a TV screen, connect the TV to the Wireless Unit.

An NOT TRANSLATEDHDMI cable (sold separately) is necessary to connect an NOT TRANSLATEDHDMI device.

  1. Connect the Wireless Unit’s NOT TRANSLATEDHDMI IN connector and the NOT TRANSLATEDHDMI device’s NOT TRANSLATEDHDMI OUT connector with an NOT TRANSLATEDHDMI cable (sold separately).
  2. To also display images from the NOT TRANSLATEDHDMI device onto a TV screen, connect the Wireless Unit’s NOT TRANSLATEDHDMI OUT connector and the TV’s NOT TRANSLATEDHDMI IN connector with an NOT TRANSLATEDHDMI cable (sold separately).

Hint

  • Connecting the IR Blaster (supplied) allows you to operate the NOT TRANSLATEDHDMI device by aiming its remote control at the projector. This is useful when the projector and NOT TRANSLATEDHDMI device are placed at distant locations.
  • The projector does not support interlaced signals. Set the output resolution of the NOT TRANSLATEDHDMI device to “NOT TRANSLATEDAuto,” “NOT TRANSLATED1080p,” or “NOT TRANSLATED720p.”

[14] PreparingConnecting another device to the Wireless UnitConnecting the IR Blaster

By connecting the Wireless Unit and an NOT TRANSLATEDHDMI device with the IR Blaster (supplied), you can operate the NOT TRANSLATEDHDMI device by aiming its remote control at the projector. This is useful when the projector and NOT TRANSLATEDHDMI device are placed at distant locations.

  1. Connect the IR Blaster to the NOT TRANSLATEDIR BLASTER connector of the Wireless Unit.

  2. Mount the NOT TRANSLATEDIR BLASTER head on the NOT TRANSLATEDHDMI device so that the head is aimed at the remote control receiver of the device.

    To locate the remote control receiver, refer to the instruction manual supplied with the NOT TRANSLATEDHDMI device.

  3. Aim the NOT TRANSLATEDHDMI device’s remote control at the projector’s remote control receiver (a), then operate the remote control.

    If the NOT TRANSLATEDHDMI device does not respond, change the direction of the IR Blaster.

    After checking the IR Blaster works correctly, secure it with the double-sided adhesive sheet (supplied).

[15] How to use the special applicationThe home screen of the special application

The items displayed in the home screen of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” are described.

  1. (CONSTANT [2072]Settings) button

    Displays the setting menu.

  2. DELIMITER [NOT EC]
    (standby/power-on) button
    DELIMITER [NOT EC]
    DELIMITER [EC]
    (networked standby/power-on) button
    DELIMITER [EC]

    DELIMITER [NOT EC]
    Switches between standby and power-on.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    Switches between networked standby and power-on.
    DELIMITER [EC]

  3. Projector remaining battery life
  4. CONSTANT [2411]Poster button

    Places the projector in poster mode.

    Tap this button to project a poster, to use the screen mirroring function to project the smartphone’s screen, or to project photos or movies from a NOT TRANSLATEDDLNA device.

    The projector is automatically placed in poster mode just after it is turned on. Tap this to place it in poster mode manually.

    Tap the button under [CONSTANT [2411]Poster] to change the poster type.

  5. “CONSTANT [2410]HDMI” button

    Places the projector in “NOT TRANSLATEDHDMI” mode.

    Tap this button to project images from the NOT TRANSLATEDHDMI device connected to the Wireless Unit.

  6. (control panel) button

    Opens the control panel. You can change the screen brightness, volume, etc.

  7. CONSTANT [2412]Photo cast button

    Tap this button to project a photo or movie stored in the smartphone using the special application.

About the notification screen on the smartphone

DELIMITER [NOT EC]
When the smartphone and projector are connected, the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” is displayed in the notification screen on the smartphone. In this notification, you can switch the projector between standby and power-on, and adjust the volume.
DELIMITER [NOT EC]
DELIMITER [EC]
When the smartphone and projector are connected, the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” is displayed in the notification screen on the smartphone. In this notification, you can switch the projector between networked standby and power-on, and adjust the volume.
DELIMITER [EC]

Flick down from the top edge of the smartphone’s screen to open the notification screen. With an NOT TRANSLATEDiPhone, tap “NOT TRANSLATEDToday” (a) to see the notification of this application.


NOT TRANSLATEDAndroid smartphone

NOT TRANSLATEDiPhone

  1. DELIMITER [NOT EC]
    Standby/power-on button
    DELIMITER [NOT EC]
    DELIMITER [EC]
    Networked standby/power-on button
    DELIMITER [EC]
  2. Volume adjustment button

Hint

  • When two or more projectors are registered to the special application, the device name currently connected is displayed on the home screen.
  • The notification screen may vary depending on the smartphone.

[16] How to use the special applicationUpdating the software

The software of the projector and the Wireless Unit can be updated via the Internet. When a new version of software is available, appears on the top right of the special application’s home screen and appears at the [CONSTANT [2076]Update] item of the setting menu.

  1. Press and hold the power button of the projector to turn it on.
  2. Tap the (CONSTANT [2072]Settings) button on the home screen of “CONSTANT [2359]Portable Ultra Short Throw Projector Application.”
  3. Tap [CONSTANT [2076]Update] — [CONSTANT [2134]Update].
  4. Tap [CONSTANT [2142]Get update], then follow the on-screen instructions to update the software.

    The Wireless Unit update is performed when playing back images from the NOT TRANSLATEDHDMI device connected to the Wireless Unit.

Hint

  • Connect the projector to an access point (wireless router) to update.
  • It is recommended that you connect the smartphone via NOT TRANSLATEDWi-Fi to download the update file because the file size may be large.
  • and are displayed when [CONSTANT [2132]Update notifications] in [CONSTANT [2076]Update] is enabled. It is enabled by default.

[17] Projecting the posterProjecting the clock

In poster mode, you can project the clock.

Connect the smartphone and projector to the same access point (wireless router) before using this function.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the button under [CONSTANT [2411]Poster].
  3. Select the desired clock type.

[18] Projecting the posterProjecting weather information

In poster mode, you can project weather information of the current location. The weather information is updated every hour.

Connect the smartphone and projector to the same access point (wireless router) before using this function.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the button under [CONSTANT [2411]Poster].
  3. Tap [CONSTANT [2049]Weather].
  4. Tap [CONSTANT [2202]Update location information], then follow the on-screen instructions to set the location information.

Note

  • If new weather information is not obtained, the weather information display is not updated.

[19] Projecting the posterProjecting a slideshow

In poster mode, you can project a slideshow. In addition to choosing one from prepared genres, you can use photos stored in the smartphone to project in a slideshow.

Connect the smartphone and projector to the same access point (wireless router) before using this function.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the button under [CONSTANT [2411]Poster].
  3. Select a slideshow genre (such as [CONSTANT [2336]A day]), or [CONSTANT [2335]My slideshow].
  4. When selecting [CONSTANT [2335]My slideshow], select photos and movies to be projected in a slideshow from the thumbnail screen, tap [CONSTANT [2238]Build Slideshow], then follow the on-screen instructions to complete the setting.

    You can transfer photos and movies until [CONSTANT [2212]Free space: ] of the projector is filled.

    Tap [CONSTANT [2305]All] (NOT TRANSLATEDAndroid smartphone) or the button (NOT TRANSLATEDiPhone) to change the storing location of photos and movies.

To change photos and movies of [CONSTANT [2335]My slideshow]

Tap the button to the right of [CONSTANT [2335]My slideshow], then reselect photos and movies from the thumbnail screen. Tap [CONSTANT [2238]Build Slideshow] to upload them and overwrite the photos and movies previously stored in the projector.

To set the playback order of [CONSTANT [2335]My slideshow]

In the my slideshow screen, tap the (CONSTANT [2217]Playback order) button. You can select [CONSTANT [2219]Newest first], [CONSTANT [2220]Oldest first], or [CONSTANT [2221]Random] as the playback order.

To set the background music for [CONSTANT [2335]My slideshow]

In the my slideshow screen, tap the (CONSTANT [2205]Background music) button. You can select multiple tracks of background music to be played back in the order of selection.

You can select [CONSTANT [2207]Edit] in the music list screen to add, sort, and remove music.

Hint

  • You can set the slideshow interval time.
  • The projector can play back audio files in the following formats. Audio files in other formats may be displayed in the list, though those files cannot be played back.
    • NOT TRANSLATEDMPEG2 AAC (NOT TRANSLATEDAAC-LC)
    • NOT TRANSLATEDMPEG4 AAC-LC
    • NOT TRANSLATEDMPEG1 Layer 1/2
    • NOT TRANSLATEDMP3 (NOT TRANSLATEDMPEG1 Layer 3)
    • NOT TRANSLATEDLPCM

[20] Projecting the posterChanging the settings of the poster display

You can change the location for the weather information, and the photo change interval for [CONSTANT [2336]A day] and [CONSTANT [2335]My slideshow].

Connect the smartphone and projector to the same access point (wireless router) before using this function.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the button under [CONSTANT [2411]Poster].
  3. Tap the (CONSTANT [2340]Poster settings) button.
  4. Select the item to be set.

Setting items

[CONSTANT [2051]Weather settings]

Tap [CONSTANT [2202]Update location information], then follow the on-screen instructions to set the location for obtaining weather information.

[CONSTANT [2218]Display time]

Set the photo change interval for [CONSTANT [2336]A day] and [CONSTANT [2335]My slideshow].

[CONSTANT [2360]10 sec.], [CONSTANT [2223]5 min.], [CONSTANT [2224]30 min.], [CONSTANT [2225]1 hr.], [CONSTANT [2226]12 hr.], [CONSTANT [2227]1 day]

[21] Projecting a smartphone’s photo/movieProjecting a smartphone’s photo/movie

You can project a photo or movie stored in a smartphone using the special application.

Connect the smartphone and projector to the same access point (wireless router) before using this function.

Note

  • When no access point is available, place the projector in NOT TRANSLATEDWi-Fi Direct mode to connect the smartphone directly.
  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap [CONSTANT [2412]Photo cast].
  3. Select the desired photo or movie.

    When selecting a photo, you can tap the (rotate) button to rotate the photo; each tap rotates it 90 degrees clockwise.

    During movie playback, you can tap the (play) button or (pause) button to play/pause.

    Tap [CONSTANT [2305]All] (NOT TRANSLATEDAndroid smartphone) or the button (NOT TRANSLATEDiPhone) to select a photo or movie stored in another location.

Hint

  • Tap the (control panel) button to adjust the volume, brightness, etc.

[22] Using the mirroring function to project the smartphone’s screenUsing the mirroring function to project the smartphone’s screen

When your smartphone supports NOT TRANSLATEDMiracast, you can directly project the smartphone’s screen.

No access point (wireless router) connection is needed.

Note

  • Depending on your smartphone, some Internet contents cannot be projected by the mirroring function.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap [CONSTANT [2411]Poster] to place the projector in poster mode.
  3. Place the smartphone in mirroring mode, then connect it to the projector.
  4. Operate the smartphone to project the screen.

[23] Projecting photos/movies from a DLNA deviceProjecting photos/movies from a NOT TRANSLATEDDLNA device

You can project photos and movies stored in a NOT TRANSLATEDDLNA compatible device (such as a NOT TRANSLATEDBlu-ray Disc recorder) on the home network.

Before using this function, connect the smartphone and projector to the access point (wireless router) to which the NOT TRANSLATEDDLNA compatible device is connected.

Note

  • A NOT TRANSLATEDDLNA compatible application (such as Video & TV SideView) must be installed on the smartphone to project photos and movies in a NOT TRANSLATEDDLNA compatible device.
  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap [CONSTANT [2411]Poster] to place the projector in poster mode.
  3. Start the NOT TRANSLATEDDLNA compatible application.
  4. Set the projector as the output destination, then display the photo or movie.

Hint

  • The maximum still image size for projecting via NOT TRANSLATEDDLNA is 32 mega pixels (8,192 × 4,096 pixels) for NOT TRANSLATEDJPG, and 3 mega pixels (2,048 × 1,024 pixels) for NOT TRANSLATEDPNG/NOT TRANSLATEDGIF.

[24] Projecting images from the HDMI device connected to the Wireless UnitProjecting images from the NOT TRANSLATEDHDMI device connected to the Wireless Unit

You can project images stored in an NOT TRANSLATEDHDMI device.

You can connect a TV to the Wireless Unit to display NOT TRANSLATEDHDMI device’s images on both the projector and TV without changing the cable connection.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap [CONSTANT [2410]HDMI].
  3. Operate the NOT TRANSLATEDHDMI device to play back images to be projected.

Hint

  • Connecting the IR Blaster (supplied) allows you to operate the NOT TRANSLATEDHDMI device by aiming its remote control at the projector. This is useful when the projector and NOT TRANSLATEDHDMI device are placed at distant locations.

[25] SettingsAdjusting the volume/pictureAdjusting the volume

You can adjust the volume of the projector.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (control panel) button.
  3. Use the slide bar of [CONSTANT [2036]Volume] to adjust.

Hint

  • You can also use the notification of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” displayed in the notification area of the smartphone to adjust the volume.

[26] SettingsAdjusting the volume/pictureAdjusting the brightness

You can adjust the brightness of the projected image.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (control panel) button.
  3. Use the slide bar of [CONSTANT [2037]Brightness] to adjust.

Automatically adjust the brightness according to ambient lighting

Tap [CONSTANT [2414]Auto]. While using with a battery, [CONSTANT [2414]Auto] is disabled.

[27] SettingsAdjusting the volume/pictureAdjusting the focus

You can adjust the focus of the projected image.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (control panel) button.
  3. Tap the / buttons in [CONSTANT [2039]Focus] to adjust.

Auto focusing

Tap [CONSTANT [2414]Auto].

Note

  • The auto focus function uses the range sensor on the rear of the projector to measure the distance to the projection surface and adjusts the focus. In the following conditions, the range sensor may not be able to measure the distance correctly and the focus may not be adjusted:
    • There is an obstruction between the projector and the projection surface
    • The projector is placed on a stand or the like.
    • The AC adaptor connected to the projector blocks the range sensor (a).

  • When the projected image size is 60 inches or more, the auto focus function does not work.
  • Depending on the projector’s location and the material of the projection surface, the auto focus function may not work correctly.
  • If the auto focus function does not work, disable [CONSTANT [2414]Auto], then adjust manually.

[28] SettingsAdjusting the volume/pictureKeystone correction

The correction method varies depending on the skew of the projected image.

When the lengths of the top edge and bottom edge of the projected image differ

Use the special application to perform keystone correction.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (control panel) button.
  3. Use the slide bar or / buttons of [CONSTANT [2040]Keystone correction] to adjust.

When the lengths of the left edge and right edge of the projected image differ

Change the projector’s location or orientation to project perpendicularly.

[29] SettingsAdjusting the volume/pictureRotating the projected image

You can rotate the projected image 180 degrees.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (control panel) button.
  3. Tap the button or button.

    Tap the button to rotate the projected image 180 degrees.

    Tap the button to return to the original orientation.

To rotate the projected image automatically

Tap [CONSTANT [2414]Auto].

[30] SettingsCONDITION [NOT EC]Setting auto on/standbyCONDITION [EC]Setting auto on/networked standby

DELIMITER [NOT EC]
You can place the projector in standby mode at a specified time or when a smartphone is detected.
DELIMITER [NOT EC]
DELIMITER [EC]
You can place the projector in networked standby mode at a specified time or when a smartphone is detected.
DELIMITER [EC]

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2092]Auto on/Networked Standby].
  4. Select the item to be set.

Setting items

[CONSTANT [2106]Switch to Networked Standby after inactivity]

DELIMITER [NOT EC]
When the projector is in poster mode and not operated for more than 20 minutes in a dark room, it enters standby status and the projection screen is dimmed. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [NOT EC]
DELIMITER [EC]
When the projector is in poster mode and not operated for more than 20 minutes in a dark room, it enters networked standby status and the projection screen is dimmed. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [EC]

[CONSTANT [2107]On at a specified time]

DELIMITER [NOT EC]
At the specified time, the projector resumes from standby status and projects the image. When you tap [CONSTANT [2107]On at a specified time], the setting screen appears. Tap the switch to enable the setting, then specify the time. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [NOT EC]
DELIMITER [EC]
At the specified time, the projector resumes from networked standby status and projects the image. When you tap [CONSTANT [2107]On at a specified time], the setting screen appears. Tap the switch to enable the setting, then specify the time. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [EC]

[CONSTANT [2108]Switch to Networked Standby at a specified time]

DELIMITER [NOT EC]
At the specified time, the projector enters standby status and dims the projection screen. When you tap [CONSTANT [2108]Switch to Networked Standby at a specified time], the setting screen appears. Tap the switch to enable the setting, then specify the time. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [NOT EC]
DELIMITER [EC]
At the specified time, the projector enters networked standby status and dims the projection screen. When you tap [CONSTANT [2108]Switch to Networked Standby at a specified time], the setting screen appears. Tap the switch to enable the setting, then specify the time. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [EC]

[CONSTANT [2111]On when smartphone detected]

DELIMITER [NOT EC]
When the projector detects the smartphone, it resumes from standby status and projects the image. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [NOT EC]
DELIMITER [EC]
When the projector detects the smartphone, it resumes from networked standby status and projects the image. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [EC]

[CONSTANT [2112]Switch to Networked Standby when smartphone detected]

DELIMITER [NOT EC]
When the projector detects that the smartphone has moved away, it enters standby status and dims the projection screen. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [NOT EC]
DELIMITER [EC]
When the projector detects that the smartphone has moved away, it enters networked standby status and dims the projection screen. Each time you tap the switch, the setting is switched between enabled/disabled.
DELIMITER [EC]

Hint

  • When the smartphone and projector are connected, the projector’s clock is automatically synchronized with the smartphone’s clock.
  • DELIMITER [NOT EC]
    After placing the projector in standby status by pressing the power button, if the smartphone is taken out of range of the projector and then returned within five minutes, the [CONSTANT [2111]On when smartphone detected] function may not work. In such a case, turn the projector on manually.
    DELIMITER [NOT EC]
    DELIMITER [EC]
    After placing the projector in networked standby status by pressing the power button, if the smartphone is taken out of range of the projector and then returned within five minutes, the [CONSTANT [2111]On when smartphone detected] function may not work. In such a case, turn the projector on manually.
    DELIMITER [EC]

[31] SettingsAdjusting the picture settings

You can adjust the picture settings of the projector.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2073]Picture].
  4. Select the item to be adjusted.

Setting items

[CONSTANT [2086]Preset 1]

This option is suited to projecting onto a white wall, table or floor.

[CONSTANT [2087]Preset 2], [CONSTANT [2088]Preset 3]

This option is suited to projecting onto a yellowish wall, table or floor. Select the desired color tone.

[CONSTANT [2089]Custom 1], [CONSTANT [2090]Custom 2]

By default, [CONSTANT [2089]Custom 1] is adjusted to a brightness-oriented setting, and [CONSTANT [2090]Custom 2] is adjusted to be suited to natural images.
You can tap the button to adjust to one of the following settings:
[CONSTANT [2094]Saturation], [CONSTANT [2095]Brightness], [CONSTANT [2096]Contrast], [CONSTANT [2098]Sharpness], and [CONSTANT [2099]White balance]

Tap [CONSTANT [2103]Reset] to reset to the default settings.

[32] SettingsAdjusting the sound quality (NOT TRANSLATEDxLOUD)


“NOT TRANSLATEDxLOUD” is an audio playback technology for improving the playback level. You can enjoy dynamic and powerful sound with movies, etc.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap (CONSTANT [2072]Settings).
  3. Tap [CONSTANT [2074]Sound].
  4. Tap the [CONSTANT [2155]xLOUD] switch to change between enabled and disabled.

[33] SettingsConfiguring the network settingsChanging the device name of the projector

You can change the projector’s name displayed on the home network. “NOT TRANSLATEDLSPXP1” is set at the time of purchase.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2075]Network].
  4. Tap [CONSTANT [2113]Device].
  5. Enter the new name.

Hint

  • After changing the device name, it is displayed on the home screen of the special application.

[34] SettingsConfiguring the network settingsConnecting to an access point

A connection between the projector and access point (wireless router) is needed in the following situations. Connect the smartphone and projector to the same access point (wireless router).

  • When projecting photos or movies in the smartphone.
  • When operating the poster.
    (When changing the poster type, transferring photos and movies for [CONSTANT [2335]My slideshow], updating the weather information for poster mode, or using [CONSTANT [2340]Poster settings])
  • When updating the software of the unit.
  1. Connect the smartphone to the access point.
  2. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  3. Tap the (CONSTANT [2072]Settings) button.
  4. Tap [CONSTANT [2075]Network].
  5. Tap [CONSTANT [2115]Wi-Fi].
  6. Tap [CONSTANT [2018]Connect] to connect to the access point.

    If the access point requires password input, tap [CONSTANT [2011]Password] to enter the password.
    If the access point supports the NOT TRANSLATEDWPS (NOT TRANSLATEDWi-Fi Protected Setup) function, tap [CONSTANT [2418]Connect using Wi-Fi Protected Setup™], select the connection method, then follow the on-screen instructions.

To connect to an access point you have connected in the past

On the NOT TRANSLATEDWi-Fi screen, tap the button, then tap [CONSTANT [2428]Network history] to view access points you have connected in the past. Tap the desired access point.

To delete an access point

On the NOT TRANSLATEDWi-Fi screen, tap the button, then tap [CONSTANT [2429]Delete current network settings] to delete the access point currently connected to.
To delete an access point displayed in [CONSTANT [2428]Network history], touch and hold the access point to be deleted.

Hint

  • The terms “access point” and “encryption key (password)” vary depending on the manufacturer (“encryption key,” “KEY,” “NOT TRANSLATEDWEP key,” “security key,” “pass phrase,” “network key,” etc.). If you are uncertain, consult the manufacturer of the access point.
  • The NOT TRANSLATEDAOSS button of the access point may support NOT TRANSLATEDWPS. For whether or not it supports NOT TRANSLATEDWPS, refer to the instruction manual of the access point.

[35] SettingsConfiguring the network settingsConnecting via NOT TRANSLATEDWi-Fi Direct

You can directly connect this unit and a smartphone (NOT TRANSLATEDWi-Fi Direct) without using an access point (wireless router).

Note

  • When [CONSTANT [2035]Wi-Fi Direct] is enabled, screen mirroring of the smartphone’s screen is not available. Also, [CONSTANT [2035]Wi-Fi Direct] is disabled when establishing a connection with an NOT TRANSLATEDHDMI device.
  • When [CONSTANT [2035]Wi-Fi Direct] is enabled, the smartphone establishes a peer-to-peer connection with the projector, therefore it is unable to establish a NOT TRANSLATEDWi-Fi connection with an access point (wireless router). After use, disable [CONSTANT [2035]Wi-Fi Direct].
  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2075]Network].
  4. Tap [CONSTANT [2035]Wi-Fi Direct].
  5. Tap the switch of [CONSTANT [2035]Wi-Fi Direct] to enable it.

    [CONSTANT [2362]Wi-Fi Direct: On] appears on the home screen or photo cast screen of the special application. If your smartphone is an NOT TRANSLATEDAndroid smartphone, it connects to this unit automatically. If you are using an NOT TRANSLATEDiPhone, or your NOT TRANSLATEDAndroid smartphone does not connect automatically, use the NOT TRANSLATEDWi-Fi setting screen of the smartphone to connect to this unit.

To disable [CONSTANT [2035]Wi-Fi Direct]

Tap the switch of [CONSTANT [2035]Wi-Fi Direct].

[36] SettingsConfiguring the network settingsChecking the signal strength

You can check the signal strength of the Wireless Unit, access point (wireless router) and smartphone which are connected to the projector via a wireless LAN.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2075]Network].
  4. Tap [CONSTANT [2191]Signal strength].

Hint

  • Tap the (refresh) button to refresh the signal strength indication.

Note

  • The signal strength of the Wireless Unit is displayed only when the projector is in NOT TRANSLATEDHDMI mode.
  • The signal strength of the access point (wireless router) is displayed only when it is connected to the projector. It is not displayed when the mirroring function is used to project the smartphone screen.

[37] SettingsConfiguring the network settingsConfirming registration when connecting a smartphone


When an unregistered smartphone accesses the projector, you can have a confirmation screen displayed to restrict the automatic registration.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2075]Network].
  4. Tap the [CONSTANT [2117]Restrict adding smartphones] switch to switch between enabled and disabled.

    When enabled, PIN code input is required to connect an unregistered smartphone. The PIN code is displayed on the projection screen.

[38] SettingsConfiguring the network settingsManaging smartphones to be connected


You can allow/deny access from each smartphone registered to the projector. You can also delete a registration.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2075]Network].
  4. Tap [CONSTANT [2119]Smartphones added].
  5. Tap the device to be changed.
  6. Select [CONSTANT [2130]Allow] or [CONSTANT [2131]Deny ].

    To delete the registration, tap [CONSTANT [2192]Delete smartphone].

Note

  • Even when the registration has been deleted, the deleted device will be registered to the access device list if the device accesses the projector.

    To deny the automatic registration, enable [CONSTANT [2117]Restrict adding smartphones].

  • You can set [CONSTANT [2131]Deny ] to up to seven devices.

[39] SettingsSetting the language for the projector

[40] SettingsUpdating the software

The software of the projector and the Wireless Unit can be updated via the Internet. When a new version of software is available, appears on the top right of the special application’s home screen and appears at the [CONSTANT [2076]Update] item of the setting menu.

  1. Press and hold the power button of the projector to turn it on.
  2. Tap the (CONSTANT [2072]Settings) button on the home screen of “CONSTANT [2359]Portable Ultra Short Throw Projector Application.”
  3. Tap [CONSTANT [2076]Update] — [CONSTANT [2134]Update].
  4. Tap [CONSTANT [2142]Get update], then follow the on-screen instructions to update the software.

    The Wireless Unit update is performed when playing back images from the NOT TRANSLATEDHDMI device connected to the Wireless Unit.

Hint

  • Connect the projector to an access point (wireless router) to update.
  • It is recommended that you connect the smartphone via NOT TRANSLATEDWi-Fi to download the update file because the file size may be large.
  • and are displayed when [CONSTANT [2132]Update notifications] in [CONSTANT [2076]Update] is enabled. It is enabled by default.

[41] SettingsResetting to the initial settings

You can reset the special application to the initial settings. A reset does not affect slideshows and background music transferred to the projector.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2152]Reinitialise].
  4. Tap [CONSTANT [2153]Reinitialise settings], then follow the on-screen instructions to perform the initialization.

[42] SettingsDeleting contents stored in the projector


You can delete images and background music transferred to the projector.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap [CONSTANT [2152]Reinitialise].
  4. Tap [CONSTANT [2154]Reinitialise content], then follow the on-screen instructions to perform the initialization.

[43] SettingsChecking the projector to be operated using the special application

When you have two or more projectors, you can register additional projectors and select the device to be operated.

  1. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  2. Tap the (CONSTANT [2072]Settings) button.
  3. Tap (Current device).

    Projectors registered to the special application are displayed. is displayed on the device currently designated to be operated.

Registering an additional projector

Tap the (add) button, then follow the on-screen instructions to register.

Changing the projector to be operated

Tap the desired projector.

[44] SettingsPairing the projector and Wireless Unit again

The projector and Wireless Unit have already been paired at the time of purchase. When the pairing is removed such as after maintenance, pair them again.

  1. Disconnect the AC adaptor from the Wireless Unit.
  2. After approximately 10 seconds, connect the AC adaptor to the Wireless Unit again.
  3. Start / (CONSTANT [2359]Portable Ultra Short Throw Projector Application) on the smartphone.
  4. Tap the (CONSTANT [2072]Settings) button.
  5. Tap [CONSTANT [2152]Reinitialise].
  6. Tap [CONSTANT [2151]Pairing Wireless HDMI Unit].
  7. Locate the NOT TRANSLATEDPAIRING button of the Wireless Unit, then tap [CONSTANT [2169]Start].
  8. Follow the on-screen instructions to pair again.

About the indicator display during pairing

During pairing, the indicator on the front panel of the Wireless Unit flashes as follows:

  • Flashing in white twice every 1.5 seconds: Attempting to pair with the projector.
  • Flashing in red: Failed to pair.

Hint

  • Press the NOT TRANSLATEDPAIRING button with a thin object such as a paper clip.

[45] Precautions/specificationsPrecautions

For your safety

  • Do not let water or foreign objects get into the unit. It may cause a fire or electric shock. If water or foreign objects have gotten into the unit, turn it off immediately, and disconnect the power cord and connection cables.
  • Do not disassemble or modify the unit. It may cause a malfunction, fire or electric shock.
  • If there is a possibility of lightning strike, do not use the unit. A lightning strike may cause an electric shock. If lightning is likely, unplug the unit to prevent a fire, electric shock and malfunction.

On safety

  • Wireless functions are incorporated into this unit. Radio waves may affect the operation of other devices. Do not use this device in the following locations.

    • On an airplane.
    • Near automatically-controlled equipment, such as automatic doors or fire alarms.

    If other equipment experiences problems such as interference while the unit is being used, immediately stop using the unit.

  • Do not continue viewing the projected screen for a long time. Continuously viewing the projected screen for a long time may cause eye strain. If you feel any discomfort or pain, immediately stop using the unit and have a rest. If the discomfort or pain persists after taking a rest, consult a doctor.
  • Do not project onto a glossy surface. The light may be reflected into your eyes and may adversely affect them.
  • Keep the unit away from children. If a cable becomes wrapped around the neck or similar misuse, it may cause an accident or injury.

On handling

  • If the unit is not to be used for a long time, unplug it.
  • Do not drop, hit, compress, or put a heavy object on the unit.
  • The operating temperature range of the unit is 5 °C to 35 °CCONDITION [U] (41 °F to 95 °F). If the unit is used in an extremely cold or hot place outside the operating temperature range, it may cause a malfunction.
  • The wireless function of the unit is designed for use in the U.S.A. only. Each country/region has its own regulations for radio wave use, therefore if you use the wireless function of the unit abroad, you may be penalized.
  • Do not place the unit where there is excessive oily smoke, steam, moisture or dust. It may cause a fire or electric shock.
  • Do not install the unit in a dangerously unsuitable location. The unit may fall causing an injury.
  • Do not subject the unit to a strong impact. If you apply a strong force to the unit, such as putting a heavy object on it, drop it, or step on it, it may cause injuries or a malfunction. Although the projection window is made of tempered glass, if it is strongly pushed or struck, it may break causing injuries.
  • Take care not to drop the unit when moving it. If the unit falls, it may break or cause injuries.

On placement

  • Do not place the unit in any places where there is excessive dust or cigarette smoke. Dust and cigarette tar adheres to components inside the unit (such as the projection window) causing a malfunction.

  • Do not place the unit in any places where the temperature is extremely hot or cold, or the humidity is extremely high. Especially when there is strong sunshine or during the summer, the inside of a car can get quite hot, and a unit left in the car may deform or malfunction.
  • Do not place the unit on an unstable surface. The unit may fall or topple over resulting in injuries.
  • Do not place the unit where there is water. It may cause a fire or electric shock.
  • Do not place/store the unit in a place exposed to direct sunlight or close to a heater. Heat may build up in the unit causing a fire.

On AC adaptor and cables

  • Do not damage the power cord. It may cause a fire or electric shock.
  • Be sure to use the supplied AC adaptor with the unit. If a different AC adaptor is used with the unit, it may cause a fire, electric shock or malfunction.
  • Do not touch the power plug with wet hands. It may cause an electric shock.
  • Before making connections with the AC adaptor and connection cables, turn off the unit and connected equipment, and unplug the power plugs from the wall outlet.
  • Do not wrap the power cord or connection cable around the AC adaptor. It may cause the cord or cable to break.
  • Before moving the unit, disconnect the power cord and connection cables. The cables may be damaged resulting in a fire or electric shock, or connected equipment may fall or topple over causing injuries.
  • Insert the connector straight. If it is inserted at an angle, pins may make a short circuit causing a fire.

On fan noise

  • A fan is incorporated inside the projector to prevent overheating, and this makes a slight noise while turned on. This noise is not a malfunction. However, if there are any abnormal noises, consult qualified NOT TRANSLATEDSony personnel.

On light source maintenance

  • This unit uses a laser, therefore special caution and facilities are necessary for the inspection and maintenance of light source components. Be sure to consult qualified NOT TRANSLATEDSony personnel.

On projector

  • Although this unit is manufactured using very high precision technology, there may be some permanent black or white pixels on the projected screen. Also, there may be striped unevenness in color or brightness. This is a result of the projector structure and is not a malfunction. The color balance of each projector unit varies; therefore, when multiple LCD projectors are used, the color reproduction among projectors may vary, even if they are of the same model.
  • Depending on viewed content, primary colors such as red, blue, or green are visible when you move your eyes or under certain conditions; this is not a malfunction. It is caused by a “color breakup” phenomenon which is specific to the field-sequential color system adopted into the unit for displaying images. This phenomenon can be subdued by diminishing the contrast between the image and the backdrop, such as decreasing the brightness of the unit or increasing the brightness of the room.

On condensation

  • If the projector is moved suddenly from a cold to a warm place, or just after a room heater is turned on in a winter morning, condensation may occur on the surface or inside of the projector. If condensation occurs, leave the projector turned off until the condensation dissipates. If the projector is used while there is condensation, it may cause a malfunction.

On ventilation holes

  • Do not block the ventilation holes (intake/exhaust). If the ventilation holes are blocked, heat will build up inside the unit, causing a fire or malfunction. To maintain good ventilation, observe the following:

    • Place the unit away from walls and objects.

    • Do not use a cover that blocks the ventilation holes.

    • Do not place the unit on a soft cloth, paper documents, thick carpet or small pieces of paper. They may be drawn in and block the intake holes.

  • Do not bring your hand or object close to the exhaust holes. It may cause burns or deformation.

On projection window

  • Do not look into the projection window. The light may damage your eyes.
  • Do not obstruct the projection window. The light will heat the obstruction, which may cause deterioration, deformation, burns or fire.

Cautions about heat generation of the unit

  • While using or charging the unit, the unit or AC adaptor may become hot; this is not a malfunction. If the unit temperature becomes excessively hot, it may automatically turn off for safety. In such a case, use it in a cooler place after the unit has cooled down.
  • If the unit or AC adaptor becomes unusually hot, it may malfunction. Immediately turn the unit off and unplug the AC adaptor from the wall outlet, then consult qualified NOT TRANSLATEDSony personnel.
  • Do not continue touching the unit in operation or the AC adaptor for a long time. Prolonged contact with the skin may result in burns. Even touching through clothing, prolonged contact may result in burns.
  • Do not use the unit or AC adaptor covered by cloth or bedding. Heat will build up causing deformation, malfunction or a fire.

On charging

  • Charge the unit in the ambient temperature of 5 °C to 35 °CCONDITION [U] (41 °F to 95 °F). The unit may not charge sufficiently outside this temperature range.
  • While charging or using the unit, the temperature of the unit may rise; this is not a malfunction.
  • If you do not use the unit for a long time, charge it every six months to prevent battery degradation.
  • When the unit has been left unused for a long time, the charging time may be longer.
  • When the battery usage time drops to half of its original time, it may have reached the end of its life span. Consult qualified NOT TRANSLATEDSony personnel about the rechargeable battery replacement.

On AC power interruption

When the unit is turned off using the power button, the power supply to the unit is not completely stopped.

To completely stop the power supply to the unit, unplug it from the wall outlet. Place the AC adaptor close to the wall outlet so that you can quickly unplug it when becoming aware of a problem.

Notes on wireless LAN

NOT TRANSLATEDSony is not liable for any loss or damage caused by loss or theft of the unit resulting in unauthorized accesses to or abuse of the equipment which is incorporated into the unit.

Notes on wireless LAN security

  • Always make sure that you are using a wireless LAN that is secured against hacking, access from malicious third parties, and other vulnerabilities. Proper security setting for a wireless LAN is very important.
  • NOT TRANSLATEDSony is not liable for any loss or damage caused by security problems resulted from failing to take security countermeasures, or unavoidable circumstances due to specifications of the wireless LAN.

If you have questions or problems, read Reference Guide, Startup Guide, and Help Guide thoroughly again. If the answer is not found, consult qualified NOT TRANSLATEDSony personnel.

[46] Precautions/specificationsCleaning

  • Be sure to unplug the unit from the wall outlet before cleaning.
  • To clean the surface of the projection window:
    Gently wipe it with a soft cloth such as an eyeglass cleaning cloth. If there are stubborn stains, wipe them up with a cloth moistened with water. Never use alcohol, benzene, thinner, acidic cleaning agents, alkaline cleaning agents, abrasive cleaning agents, chemical dust cloths, and so on.
  • To clean the exterior:
    Gently wipe it with a soft cloth. If there are stubborn stains, wipe up the stains with a soft cloth which has been soaked in diluted neutral detergent and thoroughly wrung out, then wipe the exterior again with a dry cloth. Do not use alcohol, benzene, thinner, and so on.
  • If the unit is rubbed hard with a dirty cloth, the unit may be scratched.
  • If volatile liquid such as insecticide splashes on the unit, or an item made of rubber or vinyl stays in physical contact with the unit for a long time, the unit may be affected or the surface color may fade.
  • Do not touch the projection window with bare hands.

[47] Precautions/specificationsSpecifications

Portable Ultra Short Throw Projector (NOT TRANSLATEDLSPX-P1)

Projector

Projection system

SXRD three primary colors LCD shutter projection system　

Display device

0.37 inch SXRD × 1

1366 × 768 pixels

Focus adjustment

Motor-driven (auto focus*1)

Projected image size

22 inches to 80 inches

Light source

Laser diode

Light output

100 lm


Battery

Built-in lithium-ion battery

Available operating time

Approx. 2 hours*2

Charging time

Approx. 4 hours


Audio

Speakers

Approx. 25 mm diameter × 2 (monaural) bass reflex system

Amplifier

2 W × 2 W monaural (4 ohms)

NOT TRANSLATEDxLOUD compatible


Wireless communication

Wireless LAN

NOT TRANSLATEDIEEE 802.11a/b/g/n (2.4 GHz band, 5 GHz band), NOT TRANSLATEDMIMO compatible

NOT TRANSLATEDBluetooth

NOT TRANSLATEDBluetooth 4.0 (NOT TRANSLATEDBluetooth Low Energy)


General

NOT TRANSLATEDDLNA 2.0 compatible

NOT TRANSLATEDMiracast compatible

Built-in storage

4 GB*3

Sensors

Acceleration (attitude) sensor, illumination sensor, range sensor, IR remote control receiver (IR Blaster compatible)

Compatible codecs/formats

Picture: NOT TRANSLATEDJPEG, NOT TRANSLATEDGIF, NOT TRANSLATEDPNG, NOT TRANSLATEDBMP

Movie*4: NOT TRANSLATEDMPEG-2, NOT TRANSLATEDH.264, NOT TRANSLATEDMPEG-4, NOT TRANSLATEDH.263

Smartphone application

CONSTANT [2359]Portable Ultra Short Throw Projector Application

Compatible operating systems/devices

NOT TRANSLATEDAndroid 4.4 or later (NOT TRANSLATEDBluetooth 4.0 (NOT TRANSLATEDBluetooth Low Energy) compatible)

Following devices with NOT TRANSLATEDiOS 9: NOT TRANSLATEDiPhone 4s or later, NOT TRANSLATEDiPod Touch 5th generation or later, NOT TRANSLATEDiPad 3rd generation or later, NOT TRANSLATEDiPad mini

Operating environment conditions

Temperature: 5 °C to 35 °CCONDITION [U] (41 °F to 95 °F)

Humidity: 20% to 80%

(No condensation, humidity at 35 °CCONDITION [U] (41 °F) should be 65% or less)

Power

DC 19.5 V (AC adaptor NOT TRANSLATEDVGP-AC19V77)

Power consumption

Turned on: Approx. 18 W, approx. 32 W (charging)

DELIMITER [NOT EC]
Standby: Approx. 6 W, approx. 20 W (charging)
DELIMITER [NOT EC]
DELIMITER [EC]
Networked standby: Approx. 6 W, approx. 20 W (charging)
DELIMITER [EC]

Dimensions (width × height × depth)

Approx. 80 mm × 131 mm × 131 mmCONDITION [U] (3 1/4 inches × 5 1/4 inches × 5 1/4 inches)

Mass

Approx. 930 gCONDITION [U] (2 lb 1 oz)

*1Depending on the material of the projection surface and the projector’s location, the auto focus function may not work correctly. In such cases, adjust the focus manually.

*2This operation time is when [CONSTANT [2073]Picture] is set to [CONSTANT [2086]Preset 1], the volume is set to approximately 80% and a movie is played.

*3Shared as the system area and user area.

*4The maximum playable movie size is NOT TRANSLATED1080p.

Wireless Unit (NOT TRANSLATEDLSPX-PT1)

Input/output

NOT TRANSLATEDHDMI IN connector

NOT TRANSLATEDHDMI OUT (pass-through) connector

NOT TRANSLATEDIR BLASTER connector (Mini jack)


Wireless communication

Wireless LAN

NOT TRANSLATEDIEEE 802.11a/n (5 GHz band), NOT TRANSLATEDMIMO compatible


Compatible input signal formats

NOT TRANSLATED480p, NOT TRANSLATED720p, NOT TRANSLATED1080p


General

Operating environment conditions

Temperature: 5 °C to 35 °CCONDITION [U] (41 °F to 95 °F)

Humidity: 20% to 80%

(No condensation, humidity at 35 °CCONDITION [U] (41 °F) should be 65% or less)

Power

DC 5 V (AC adaptor NOT TRANSLATEDLSPX-AC5V2)

Power consumption

Operating: Approx. 10 W max.

Dimensions (width × height × depth)

Approx. 135 mm × 35 mm × 135 mmCONDITION [U] (5 3/8 inches × 1 7/16 inches × 5 3/8 inches)

Mass

Approx. 200 gCONDITION [U] (7 oz)

Optional accessories

Floor stand NOT TRANSLATEDLSPX-PS1

Design and specifications are subject to change without notice.

[48] Precautions/specificationsBattery duration of the projector

The fully-charged projector can be used for approximately two hours.

Hint

  • This battery duration is when [CONSTANT [2073]Picture] is set to [CONSTANT [2086]Preset 1], the volume is set to approximately 80% and a movie is played.
  • Battery duration may vary depending on the ambient temperature or other factors.
  • Battery duration may vary depending on your smartphone.

[49] Precautions/specificationsTrademarks

  • Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
  • “xLOUD” is a trademark of Sony Corporation.
  • The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
  • The BLUETOOTH SMART word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license.
  • Wi-Fi, Wi-Fi Direct, Miracast, and Wi-Fi Protected Setup are trademarks or registered trademarks of Wi-Fi Alliance.
  • Google, Google logo, Android, Google Play, and YouTube are trademarks or registered trademarks of Google Inc.
  • Apple, Apple logo, iPhone, iPod touch, iPad, and iPad mini are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

All other names of systems, products, and services are trademarks or registered trademarks of their respective owners. In this manual, the ™ or ® marks are not specified. All rights which are not explicitly written in this document belong to their respective owners.

(Only as for projector)

[50] Precautions/specificationsAbout licenses

  1. MPEG-2 Video

    ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 6312 S. Fiddlers Green Circle, Suite 400E, Greenwood Village, CO 80111 U.S.A.

  2. MPEG-4 Visual

    THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR.

    (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE MPEG-4 VIDEO.

    NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C.HTTP://WWW.MPEGLA.COM

  3. MPEG-4 AVC

    THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO

    (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR

    (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO.

    NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM

    THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE. SUCH LICENSE EXTENDS TO THIS PRODUCT ONLY AND ONLY TO THE EXTENT OF OTHER NOTICES WHICH MAY BE INCLUDED HEREIN. THE LICENSE DOES NOT EXTEND TO ANY OTHER PRODUCT REGARDLESS OF WHETHER SUCH PRODUCT IS INCLUDED WITH THIS LICENSED PRODUCT IN A SINGLE ARTICLE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM

  4. VC-1

    THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR

    (i) ENCODING VIDEO IN COMPLIANCE WITH THE VC-1 STANDARD (“VC-1 VIDEO”) AND/OR

    (ii) DECODING VC-1 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE VC-1 VIDEO.

    NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PEOMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C..HTTP://WWW.MPEGLA.COM



    THIS PRODUCT IS LICENSED UNDER THE VC-1 PATENT PORTFOLIO LICENSE.SUCH LICENSE ENTENDS TO THE PRODUCT ONLY TO THE EXTENT OF OTHER NOTICES WHICH MAY BE INCLUDED HEREIN. THE LICENSE DOES NOT EXTEND TO ANY OTHER PRODUCT REGARDLESS OF WHETHER SUCH PRODUCT IS INCLUDED WITH THIS LICENSED PRODUCT IN A SINGLE ARTICLE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM

[51] Troubleshooting/frequently asked questionsFrequently asked questionsThe color is not correct.

  • Depending on the color of the projection surface, the images may not projected correctly. Select the (CONSTANT [2072]Settings) button — [CONSTANT [2073]Picture] of “CONSTANT [2359]Portable Ultra Short Throw Projector Application” to adjust the picture quality.
  • When the projector is used in a cold environment, the color may be pale or incorrect just after the projector is turned on. After a while, the color will become correct.

[52] Troubleshooting/frequently asked questionsFrequently asked questionsThe projected image is distorted.

  • When the lengths of top edge and bottom edge of the projected image differ, tap the (control panel) button on “CONSTANT [2359]Portable Ultra Short Throw Projector Application,” then adjust with [CONSTANT [2040]Keystone correction].

  • When the lengths of left edge and right edge of the projected image differ, change the projector’s location or orientation to project perpendicularly.

[53] Troubleshooting/frequently asked questionsFrequently asked questionsThere are shadows on the projected image.

  • When the projection surface is bumpy, shadows may be cast. It is recommended that you project onto a smooth and flat surface.

[54] Troubleshooting/frequently asked questionsFrequently asked questionsThe projected images flicker, or small point noises are displayed.

  • This unit uses direct laser, therefore a speckled pattern (intense grains on projected images) may appear; this is not a malfunction. This phenomenon can be relieved to some extent by making the room brighter and projecting on a non-glossy, matte surface.

[55] Troubleshooting/frequently asked questionsFrequently asked questionsThe focus cannot be adjusted

  • If the range sensor on the rear of the projector cannot measure the distance to the projection surface, the auto focus function may not work correctly. In this case:
    • Remove obstructions between the projector and the projection surface
    • Remove the projector from the stand or the like
    • Keep the AC adaptor from blocking the range sensor (a).

  • When the projected image size is 60 inches or more, the auto focus function does not work.
  • Depending on the projector’s location and the material of the projection surface, the auto focus function may not work correctly.
  • If the auto focus function does not work correctly, tap the (control panel) button on “CONSTANT [2359]Portable Ultra Short Throw Projector Application,” then disable [CONSTANT [2414]Auto]. Adjust the focus manually.

[56] Troubleshooting/frequently asked questionsFrequently asked questionsImages from the NOT TRANSLATEDHDMI device are not projected.

  • Depending on the signal strength and the location of the projector and Wireless Unit, images from the NOT TRANSLATEDHDMI devices may not be projected properly. Change the location and orientation of the projector and Wireless Unit.
  • Make sure that there are no obstructions blocking the radio wave between the projector and Wireless Unit, and make sure that the projector and Wireless Unit are not placed too far away from each other.
  • This unit does not support interlaced signals.
    If a message “CONSTANT [1046]Cannot display the wireless HDMI signal because the video is interlaced. Check the output setting of the device that is connected to the wireless HDMI.” appears, set the output resolution of the NOT TRANSLATEDHDMI output device to “NOT TRANSLATEDAuto,” “NOT TRANSLATED1080p,” or “NOT TRANSLATED720p.”

[57] Troubleshooting/frequently asked questionsFrequently asked questionsThe projection screen dims automatically, or the projection screen turns off.

  • When the projector is used in a hot environment, or the ventilation holes (intake/exhaust) are blocked, the brightness is automatically reduced to cool down the inside of the projector. If the temperature in the projector is not cooled down even when the brightness is reduced, the projection automatically stops.

[58] Troubleshooting/frequently asked questionsFrequently asked questionsPoor picture quality.

  • The projector uses wireless LAN and NOT TRANSLATEDBluetooth communication, therefore the communication range may become short depending on the environment such as an obstruction between the projector and Wireless Unit (or your smartphone), signal strength, and wall material. In such a case, change the projector’s location, or bring your device and the projector nearer to each other.
  • If the projector is used near another device which uses wireless LAN or NOT TRANSLATEDBluetooth communication, interference may occur causing low communication speed or connection failure. In such a case, move the projector away from the other radio device. If the problem persists, turn off the other radio device.

The antenna is incorporated around in the illustration.

[59] Troubleshooting/frequently asked questionsFrequently asked questionsCannot operate with the special application.

  • The projector uses wireless LAN and NOT TRANSLATEDBluetooth communication, therefore the communication range may become short depending on the environment such as an obstruction between the projector and Wireless Unit (or your smartphone), signal strength, and wall material. In such a case, change the projector’s location, or bring your device and the projector nearer to each other.
  • If the projector is used near another device which uses wireless LAN or NOT TRANSLATEDBluetooth communication, interferences may occur causing low communication speed or connection failures. In such a case, move the projector away from the other radio device. If the problem persists, turn off the other radio device.

The antenna is incorporated around in the illustration.

Features of this unit

This unit is a “Portable Ultra Short Throw Projector” utilizing a laser light source and an ultra-short focus lens.

Install the special application “CONSTANT [2359]Portable Ultra Short Throw Projector Application” to a smartphone to operate this unit. It allows you to project and enjoy images of an NOT TRANSLATEDHDMI device connected to the supplied Wireless Unit.

Just place the unit near a wall to project images of 22 to 80 inches at point-blank range. In addition to walls, this unit can project 22-inch images on a table or floor. A lithium-ion rechargeable battery and speakers are incorporated into this unit, allowing you to enjoy images anywhere without concern for cabling.

Note

  • Screen images and illustrations in this help guide may vary from the actual product.
  • Design and specifications are subject to change without notice.